Ballymena Tyres have can provide tyres for motorbikes, cars, SUV’s and even caravans. Located on Warden Street in Ballymena this family business can been keeping locals on the road for years.
Get your motorbike roadworthy at Ballymena Tyres
It is coming up to the North West 200 and the roads are starting to fill up with bikers heading out for a trip around the coast or further. With the beautiful weather this weekend we don’t blame bikers for getting a wee run out in the sun. However please be careful if you are bringing your bike out for the first time this year. Make sure you give your bike a good once over and take special care to check that your tyres are roadworthy. For full information about the North West 200 please click here to visit their website.
Photo by Joshua Reddekopp on Unsplash
Tyresafe, as always, has provided some great information for anyone heading out in the next few weeks.
PRESSURE
The correct inflation pressure is vitally important for safe handling of motorcycles, scooters and mopeds.The recommended pressure for original equipment tyres will be stated in the motorcycle owner’s manual. For fitment of aftermarket alternatives, advice should be sought from the tyre specialist or the tyre manufacturer.
Specific advice from the tyre manufacturer is recommended for tyres fitted to classic and vintage motorcycles (pre-1960) where pressures quoted in the original handbook may be inappropriate. Pressures must be adjusted appropriately for solo and for pillion and pannier loads.
It is dangerous to re-inflate a tyre which has been run flat or seriously under inflated. Such tyres should be removed for inspection by a tyre specialist. Prolonged under-inflation causes excessive flexing, deterioration of the casing and rapid wear of the tread edges. Your fuel consumption may also be adversely affected.
Over-inflation may result in an uncomfortable ride, a reduced area of contact with the road, accelerated wear on the tread centre and makes the tyre more susceptible to impact damage. Inflation pressures should be checked once a week when the tyres are cold using an accurate and reliable pressure gauge.
RUNNING-IN TYRES
The running-in period allows the tyre to settle itself onto the wheel rim, serves to “scuff-in” the tread surface and allows the rider to adjust to the feel and handling of the new tyres.
After fitment, ensure the tread surface is not contaminated in any way. Clean off any fitting lubricant, buff around the tread circumference with a dry cloth and ensure the label is removed.
Whenever new tyres are fitted, the motorcycle should be ridden cautiously and the tyres not subjected to maximum power or speed for the first 100 miles. Avoid sudden acceleration, maximum braking or hard cornering and particular care should be taken on wet or greasy road surfaces.
After 100 miles, the tyres should be checked to ensure the correct seating and inflation.
INSPECTION AND MAINTENANCE
Motorcyclists are strongly encouraged to be aware of their tyres’ visual condition such as tread depth, cracking of the tread or sidewall rubber, cuts or bulges, foreign objects, as well as being alert to any change in dynamic performance or behaviour such as air loss, noise or vibration.
Driving over potholes, kerbs and speed bumps, even at low speeds can result in the weakening or fracture of the tyre structure.
Riders experiencing an in-service impact should ensure immediate inspection by a tyre professional. Lumps and bulges can indicate internal damage and should be examined by a tyre specialist without delay.
TREAD DEPTH
Tyre treads are designed to give good wet grip but the road surface also plays a significant role in tyre to road adhesion. In general, wet grip decreases as tyre tread patterns wear down and as the depth of surface water increases. Riders should take this into consideration and reduce speed in wet conditions.
Motorcycle tyres normally have tread wear indicators in the tread grooves and as these are approached, you should consider replacement. Once the indicators are level with the tread surface the tyre should be replaced.
The legal limit of tyre tread depth in the UK for motorcycles over 50cc is 1mm across ¾ of the width of the tread pattern and with visible tread on the remaining ¼. For motorcycles up to 50cc the law requires that all the grooves of the original tread pattern must be clearly visible.
If you have a bike or scooter, or you know someone who does then please read and share this article. If you are worried about your tyres or you need to buy a new set then call Ballymena Tyres on 028 2565 2518. Click here to visit their website.